How Long Does It Take To Polish A Car
When it comes down to it, polishing your car is a process that can take anywhere from twenty minutes to hours depending on how much work you have to do.
It’s best to start off by washing and conditioning your vehicle before moving onto applying a good base coat or primer. You want to make sure that there are no dry patches where dirt could sit and oxidize.
Once those two steps are done, apply a clearcoat (or topcoat) using a roller or brush. Make sure to spread it evenly across all surfaces of the paintwork!
Then, roll it up and hit it with a foam roller to smooth out any bumps.
Use car polish
Having a nice looking vehicle is great, but unfortunately, most people do not take good care of it. When cars were new, they would get polished every few months or even years depending on how much use the vehicle gets!
These days, though, due to increased traffic congestion and environmental concerns, many vehicles are left alone for longer periods than they used to be. This does not mean that your car will start eating away at itself, but it can still look dull and boring.
To give your vehicle some love, there are several ways to do it. One of these is to invest in professional quality car polishing products and to use them correctly.
Some types of paint that come off the factory roll-on kit cannot be restored without using appropriate chemicals. Because this is important to know, let’s go over some different types of polish and what each one does.
Buff the car
The next step in professional looking your vehicle is buffing. This can be done with either dry or wet buffs. A dry buff uses products that are mixed together and then rubbed onto the surface of the car. For example, baking soda and cream for a glass-like shine, lemon oil for diesel cars and iron powder for steel vehicles!
The important thing about a dry buff is making sure you do not scratch the paintwork while rubbing it on. Globs of product may also cause dirt to get stuck under the wax which would negate the effect of protecting the paint.
For a more durable protective layer, use a spray buff such as those available at most automobile stores. These have built in protectors so that you do not need to worry about getting too much product on your hands.
After applying the spray buff, let the car sit until the coating sets before washing it off, otherwise it could wash away easily.
Let it dry
After removing all of the wax, oils, and substances that helped protect your car’s surface, your next step is to let it air-dry. Don’t push or drag the material with a blowtorch or other source of heat, as this will melt the protective layer.
Letting your vehicle “air-dry” is an important part of protecting its new look. All you need to do is wait! The best way to make sure the coating sets properly is to leave it alone.
You can now hit up your favorite restaurant and order what they call their own special sauce — I would say that applies here. Keep an eye on your car and give it some space so it can completely dry. And don’t worry if something looks funny – sometimes there are bubbles or cracks that happen during the drying process.
That’s totally okay! Sometimes it takes a little while for the chemicals to blend together and emerge as a finished product. Just keep looking at your car and waiting out any bumps in the road.
Wax the car
The next step in taking good care of your vehicle is waxing, if you have never done it before that is great! Luckily, there are many brands that offer professional quality car waxes that do not require using very much product either.
Some tips when waxing your car are to use a soft brush to apply the wax, make sure to drag the brush across all areas of the car being careful not to push the brush hard against the surface or pull it away too quickly as this may scrape off the protective layer of the paint.
Once applied, let the car sit for a few minutes until the wax has set properly and then buff out with a clean, soft cloth. You can also wash the wax off later with a hose but remember to avoid water sprays as they could start wetting the car parts where glue was used earlier.
Seal the car
Now that you have cleaned your vehicle, it is time to seal it up! This means putting on any leftover protective gel or polish that was used, as well as applying additional layers of clear coat if needed.
Most people recommend doing this at least two days after washing, and even more depending on the type of wash you performed. The reason for this is so the new layer will properly harden and lock in all the dirt and moisture that has been removed.
Sealing your car also helps prevent some types of damage such as flaking or bubbling of the paintwork due to exposure to water and dryer cycles. These can be avoided by ensuring proper sealing is done!
Keep in mind that use of aerosol products like spray-on protectants must occur within an area with good air flow to avoid fogging the windows.
Test the car for dryness
The next step in polishing your vehicle is to make sure that it is not wet before you begin. If it is, you will have to start over!
Running some errands or going somewhere during the rainy day may require drying off the vehicle first. Make sure to pull out all of the accessories like the windshield washer bottle, tool kit, etc. and air them out so they do not waterlog while you are trying to polish the surface.
Also, if possible try to let the car sit outside overnight to dry completely. This way, it does not need to be dried in an oven which could potentially cause more damage to the paint.
Check the car for stains
The next thing you should do is check your vehicle for visible surface stains. You don’t want to spend time cleaning up the car only to find out it was stained before!
Many people begin to polish their cars at home by using wax, rubbing alcohol or both as polishes. While these are good starting points, they may not be the right solution for every stain that comes along.
Some types of stains require an acid-based cleaner such as spray cleaners or detergents to work properly. If this is the case, then you must make sure those products are appropriate for use on vehicles.
Be careful not to overdo it when washing and drying your car because this could cause water marks or rusty streaks which would negate the effort put into keeping the car clean.
Check the car for leaks
While you’re trying to polish the car, make sure to check it for any signs of water damage. If you notice any wet spots or fluid leaking out, stop immediately!
You don’t want to spend time cleaning the vehicle only to find that it has already dried up and you have made more work for yourself.
Also, be careful not to scratch the surface you are polishing. You do not need too much pressure when buffing and rubbing the coat down as this could cause scratches which would negate the benefits of using a protective coating in the first place.
Once you have done your best to clean the car and prevent water from dripping onto other surfaces, then it is time to apply a clearcoat.